Mon–Fri 9am–5pm · (902) 755-6532

Shovelhead · 1978–1984

Shovelhead 80 Horsepower Calculator

A stock Shovelhead 80 makes about 45 hp and 56 ft-lb at the rear wheel. Found in the FLH, FX, Super Glide, Low Rider, Wide Glide. Add the parts on your bike and the ones you're considering to estimate what your build will make.

Stock
45 hp
56 ft-lb
Stage 1
51 hp
61 ft-lb
Stage 2
56 hp
65 ft-lb
45 hp / 56 ft-lbDetails ↓

1Choose your engine

FLH, FX, Super Glide, Low Rider, Wide Glide.

2Your parts

Tell us what's already installed on your bike, then pick what you'd like to add or upgrade. Choose a manufacturer, then the model, and we'll show the impact and flag any supporting parts it needs.

Quick start with a stage

Fills in a typical parts list for that stage. You can change any part afterwards.

Air intake

A high-flow air cleaner lets the engine breathe.

Exhaust

2-into-1 systems make the most power. Slip-ons and drag pipes are mostly about sound.

Carburetor & jetting

Carbureted engines need re-jetting or a performance carb to match breathing mods.

Ignition

Programmable ignition lets us set timing to suit your build.

Camshaft

The single biggest bolt-in change to how your engine pulls.

Supporting parts

No horsepower on their own, but they keep a modified engine reliable.

Barnett Heavy-Duty Clutch SpringHolds the extra torque so the clutch doesn't slip.

Anything already done that isn't listed, like head work, compression pistons, a different throttle body or an older tune. It goes with your quote request but isn't included in the estimate.

Part availability and fitment vary by model and year. We confirm compatibility with your exact bike before ordering anything.

Estimated power curve

An illustration of where your Shovelhead 80 makes its power, not a dyno chart. Peaks match the estimates above; the shape reflects your parts. Torque cams fatten the bottom end, top-end cams move power higher up the rev range, and big bores bring torque in earlier.

Stock

Horsepower

hp at the rear wheel
10203040502,0002,5003,0003,5004,0004,500Stock 45

Torque

ft-lb at the rear wheel
40455055602,0002,5003,0003,5004,0004,500Stock 48

Add parts or pick a stage above to compare your build with stock.

Shovelhead 80 Stage 1 & 2 Horsepower

Estimated rear-wheel output for a typical build at each stage. These are common parts combinations, not the only way to build each stage. Open any of them in the calculator to swap parts.

StageTypical partsEst. hpEst. ft-lb
Stock—4556
Stage 1S&S Cycle Teardrop (for S&S carbs), Thunderheader 2-into-1, S&S Cycle Super E5161Open →
Stage 2S&S Cycle Teardrop (for S&S carbs), Thunderheader 2-into-1, S&S Cycle Super E, Andrews B Grind5665Open →

Best Cams for the Shovelhead 80

Estimated rear-wheel output for every cam in our database on a Shovelhead 80 with a high-flow air cleaner, a 2-into-1 exhaust and a performance carburetor (≈ 51 hp / 61 ft-lb before the cam).

CamCharacterEst. hpEst. ft-lbGain
Andrews B GrindMid-range5665+5 hp / +4 ft-lb
Andrews A GrindLow-end torque5565+4 hp / +4 ft-lb

Want a side-by-side across all engines? See the Harley cam comparison chart.

Exhaust Options for the Shovelhead 80

Estimated gain from each exhaust on a Shovelhead 80 that already has a high-flow intake and carb work. 2-into-1 systems make the most power; slip-ons and drag pipes are mostly about sound.

ExhaustTypeEst. gain
Thunderheader 2-into-12-into-1 · Classic+3 hp / +3 ft-lb

Shovelhead 80 FAQ

How much horsepower does a stock Shovelhead 80 make?

A healthy stock Shovelhead 80 makes roughly 45 hp and 56 ft-lb of torque at the rear wheel. Factory figures are measured at the crankshaft, so they're higher than what a dyno shows at the wheel.

How much horsepower does a Stage 1 Shovelhead 80 make?

A Stage 1 Shovelhead 80 (high-flow air cleaner, 2-into-1 exhaust and a tune) makes roughly 51 hp and 61 ft-lb at the rear wheel, about 6 hp more than stock. A typical parts list is the S&S Cycle Teardrop (for S&S carbs), Thunderheader 2-into-1 and S&S Cycle Super E.

How much horsepower does a Stage 2 Shovelhead 80 make?

A Stage 2 Shovelhead 80 (Stage 1 plus a performance cam) makes roughly 56 hp and 65 ft-lb at the rear wheel, about 11 hp more than stock. A typical parts list is the S&S Cycle Teardrop (for S&S carbs), Thunderheader 2-into-1, S&S Cycle Super E and Andrews B Grind.

How much horsepower does a cam add to a Shovelhead 80?

On top of a high-flow air cleaner, a 2-into-1 exhaust and a performance carburetor, a cam takes a Shovelhead 80 to roughly 55–56 hp depending on the grind. In our estimates the Andrews B Grind makes the most peak power (≈ 56 hp) and the Andrews B Grind makes the most torque (≈ 65 ft-lb).

Does a Shovelhead 80 need a tune after an exhaust or air cleaner?

Yes. A carbureted engine needs re-jetting, or a performance carb like an S&S Super E, to match a freer intake and exhaust. Otherwise it runs lean.

Other Engines

Build it with Arch Customs

Harley-Davidson specialists in Stellarton, Nova Scotia. We install, tune and dyno every part in this calculator.

Start from intake, exhaust & tune →
(902) 755-6532
Book Service